Synthesis of Star-Shaped Discotic Liquid Crystal Trimers via Co₂(CO)₈-Catalyzed [2 + 2 + 2] Cycloaddition

The synthesis of star-shaped discotic liquid crystal (DLC) trimers based on triphenylene units using a Co₂(CO)₈-catalyzed terminal alkyne [2 + 2 + 2] cycloaddition reaction is reported. These trimers consist of three triphenylene discogenic cores connected to a central 1,2,4-trisubstituted benzene ring through flexible alkyl spacers. The trimers were efficiently prepared in yields ranging from 36% to 71% by reacting monomers with 10 mol % Co₂(CO)₈ catalyst under reflux conditions in 1,4-dioxane. The liquid crystalline behavior was systematically investigated using polarizing optical microscopy (POM), differential scanning calorimetry (DSC), and X-ray diffraction (XRD). Trimer 4, featuring an ester linkage and a longer spacer, exhibited a rectangular columnar mesophase (Colro). In contrast, trimers 5b and 5c, which possess ether linkages and shorter spacers, displayed a hexagonal columnar mesophase (Colho). This study highlights the critical influence of both the connecting functional group and the length of the flexible spacer between the central benzene core and the triphenylene units on the formation and stability of the mesomorphic phases.

The preparation of key intermediates followed a simplified one-pot method. The intermediate 1,2-hydroxy-3,6,7,10,11-pentakis(pentyloxy)triphenylene was synthesized accordingly. Undec-10-yn-1-yl p-toluenesulfonate was prepared via LiAlH₄ reduction of the corresponding acid followed by tosylation. Monomers 2 and 3a–c were obtained through direct esterification or etherification reactions between phenol 1 and appropriate alkynes: 10-undecynoic acid, undec-10-yn-1-yl p-toluenesulfonate, 5-chloro-1-pentyne, or propargyl bromide. The star-shaped DLC trimers 4 and 5a–c were then synthesized via self-trimerization of monomers 2 or 3a–c under Co₂(CO)₈ catalysis. Moderate yields were observed for trimers 4, 5a, and 5b, while trimer 5c showed lower yield, likely due to steric hindrance from its shorter spacer. Despite this, the overall synthetic efficiency was satisfactory given the molecular complexity.

Two regioisomeric products can form during the trimerization of mono-substituted alkynes—1,2,4- and 1,3,5-trisubstituted benzenes. These isomers could not be separated by standard chromatographic techniques but were distinguishable by ¹H NMR spectroscopy. The presence of a signal at ~6.83 ppm (for 4), 6.81 ppm (for 5a), and 7.03 ppm (for 5b) confirmed the 1,3,5-trisubstituted pattern, whereas no such signal appeared for 5c. Integration data indicated that the 1,2,4-isomer dominated (>95%) in 4, 5a, and 5b, while 5c exclusively formed the 1,2,4-trisubstituted benzene core. This confirms the high selectivity of the Co₂(CO)₈-catalyzed reaction toward the desired structural motif.

Thermal analysis revealed distinct mesomorphic behaviors. POM and DSC results demonstrated that monomers 2, 3a, 3b, and 3c all exhibit homeotropic alignment typical of hexagonal columnar (Colh) phases. Trimer 4 displayed a stable Colro mesophase with a clearing point at 110 °C upon heating and reorganization at 100 °C upon cooling, showing no crystallization even after cooling to −50 °C. Trimer 5a failed to exhibit any mesomorphic behavior, undergoing only a single phase transition at around 15–25 °C, consistent with a crystal-to-isotropic transition. However, trimers 5b and 5c both showed clear Colho mesophases with reversible transitions: 106 °C (heating) and 104 °C (cooling) for 5b; 125 °C (heating) and 101 °C (cooling) for 5c. No crystallization was observed in either case.2,3-Dimethylindole custom synthesis

XRD analysis further confirmed the mesophase types.Zinc Protoporphyrin References Trimer 4 exhibited two strong peaks at 3.PMID:35265095 7° and 4.7° (d = 23.78 Å and 18.80 Å), characteristic of a rectangular columnar structure. In contrast, 5b and 5c showed a single intense peak near 3.8° or 4.5°, along with a broad halo at ~18° and a core–core distance peak at 3.5–3.7 Å, indicating a hexagonal arrangement. The lattice parameters derived from XRD confirmed the Colho nature of 5b and 5c, while the unique diffraction pattern of 4 supported the Colro assignment. Temperature-dependent XRD confirmed the thermal stability of these phases.

This work demonstrates that both the chemical nature of the linker (ester vs. ether) and the length of the spacer significantly affect mesophase formation. The ester group enhances intermolecular dipole–dipole interactions, stabilizing the Colro phase in 4. Shorter spacers in 5b and 5c promote tighter packing and higher symmetry, favoring the Colho phase. In contrast, the weaker polarity and bulkier structure of 5a disrupt ordering, preventing mesophase formation. Thus, precise control over molecular architecture enables tailored self-assembly and enhanced functionality.

In conclusion, the Co₂(CO)₈-catalyzed [2 + 2 + 2] cycloaddition provides a powerful and efficient route to synthesize well-defined star-shaped DLC trimers with tunable mesomorphic properties. The ability to access stable Colro and Colho phases over wide temperature ranges makes these materials promising candidates for applications in organic electronics, particularly in solution-processed devices such as OFETs and OPVs. This methodology opens new avenues for designing advanced liquid crystalline materials with predictable supramolecular organization.MedChemExpress (MCE) offers a wide range of high-quality research chemicals and biochemicals (novel life-science reagents, reference compounds and natural compounds) for scientific use. We have professionally experienced and friendly staff to meet your needs. We are a competent and trustworthy partner for your research and scientific projects.Related websites: https://www.medchemexpress.com